This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Arch stanton
Pages: 1 ... 17 18 [19] 20 21 ... 27
271
« on: December 11, 2018, 05:44:52 AM »
That's right.
But very few had them fitted. They definitely sounded best on the 500/4.
272
« on: December 10, 2018, 09:35:35 PM »
Pissing in a bottle.
You're not a truck driver by any chance?
273
« on: December 10, 2018, 09:32:59 PM »
Ah, funny you should mention Marvin pipes.
My current 750k1 project will be fitted with a original unbaffled Marvin! With bell mouths. So it should howl a bit.
Sean.
274
« on: November 21, 2018, 01:12:53 PM »
What you need next is a CB175K0.
Then I can sell you. The nos rear fender I have.
Sean.
275
« on: November 19, 2018, 12:47:35 PM »
Thanks for your input.
I shall leave it off.
Regards.
Sean.
276
« on: November 18, 2018, 11:44:46 AM »
Hello.
When I stripped my current 750k1 project. The wiring was a home made rats nest. So I just cut everything out.
But now I am installing a new harness & when looking through my box of electrical components I find a Diode. This was fitted to the bike when I got it. But the parts book doesn't show the K1 having a Diode.
I believe this Diode is to allow the bike to start in gear with the clutch pulled in.
My question is. Can this Diode be fitted into a standard K1?
And if so. Where does it go?
I'm afraid that I'm a real Dimmock where electrics are concerned.
Your help would be greatly appreciated.
Sean.
277
« on: November 03, 2018, 05:21:34 PM »
Double discs convertion bolts in the wrong way round.
So the nuts caught the speedo drive.
Derrrr!
278
« on: November 03, 2018, 04:12:08 PM »
All sorted now.
It was only one of those Derrrr! Moments that strike when too tired.
Thank you any way.
Sean.
279
« on: November 03, 2018, 03:36:26 PM »
Everything looks to be good.
But something obviously isn't.
280
« on: November 03, 2018, 02:50:34 PM »
The nut is the right way. Spanner side inwards.
281
« on: November 03, 2018, 02:30:52 PM »
Just trying to install the front spindle.
But as soon as I get the spindle nut even hand tight.
The spindle binds.
Anyone any ideas what may be wrong?
Sean.
282
« on: October 29, 2018, 08:40:01 PM »
Yes indeed.
A spelling mistake on my part I do apologise to those of a pedantic bent.
But you got my gist.
Poor spelling & grammar is one thing.
But it is damn bad manners to point it out.
Regards as always
Sean.
283
« on: October 29, 2018, 01:46:38 PM »
Answered my own question.
The answer is Yes.
284
« on: October 28, 2018, 07:36:46 PM »
That's why I won't use Americanisms
Like Tightanium for instance.
But I think everyone will get the gist of my original post.
So I shall await the answer to my question.
Sean.
285
« on: October 28, 2018, 05:41:33 PM »
Well Rob.
Make sure it's a French Omelette. As they only use one egg.
Because in France. One egg is un ouef!
Pages: 1 ... 17 18 [19] 20 21 ... 27
|
Show Posts